Introduction: Face Masquerade party With Breathing Valve

This is a face mask with breathing valve and PM2.5 filter pocket.

Supplies

-LINK to Pattern: https://www.properfitclothing.com/product-page/fa...

-LINK to Bias tape folder kit: https://amzn.to/2ynuhnw

-LINK to Bias Tape: https://goo.gl/rtMLte

-LINK to Industrial Bias Tape Attachment: https://amzn.to/2Ua3It3

-LINK to Fabric: https://amzn.to/2lNrnly

-LINK to Facing: https://amzn.to/2QkCcb8

-LINK to Breathing Valve: https://amzn.to/39ejp9v

-LINK to Breathing Valve 2: https://amzn.to/3eM2rAF

-LINK to Braided Chewy: https://amzn.to/3aVfkX9

-LINK to Ear Elastic(soft on ears): https://amzn.to/3bZuw6X

LINK to PM2.5 Filter: https://amzn.to/2Sp5FSg

-LINK to Clothed Wire Tie: https://amzn.to/2wfnmvA

-LINK to Turn Ties: https://amzn.to/2V81bB8

-LINK to Elastic Cord Stopper: https://amzn.to/35qFhwQ

Step 1: Gather Supplies

-Fabric outer layer: .25 yards (cotton, or any textile that is tightly woven)

-Framework lining: .25 yards (non stretch soft cotton)

-Bias tape: Extra wide

-Braided Elastic 1/8in(.32cm): 24 inches

-Cord (optional)

-Sweet-breathed valve: 1

-PM2.5 separate out

-Printable Pattern

Step 2: Cut Pattern

-Advance important panel: Cut 1

-Figurehead and liner bottom panel: Cut 1 outer level fabric. Cut 1 facing fabric.

-Liner side board: Cut 2 liner fabric

-Center lining control board: Cut 1 liner fabric

Step 3: Hem Lining

-Mark the hem lines on the lining panels and lining side panels.

-Roster over and pin edge.

-Sew at .25 inch wrinkle allowance.

Step 4: Lining Peak

-Place the right sides together.

-Sew as close A you can to the edge.

Step 5: Seize Facing Panels

-Intersection the center lining venire with the side lining panels.

-Flip-flop stitch where panels overlap

-Stitch as close as you can to the edge.

Step 6: Attach Lining Bottom

-Line up notch points on bottom lining and center lining panels.

-Pin bottom in to office.

-Sew at .25 inch seam allowance.

Step 7: Outer Layer Channelize

-Place redress sides together.

-Sew as close every bit you can to the edge.

-Trim furrow allowance.

Step 8: Attach Bottom

-Come up notches.

-Pin

-Tailor with .25 inch seam allowance.

-This stair is finished the same way as lining.

Maltreat 9: Place Outer Layer and Liner Together

-Place the outer bed and facing together. Make sure ill-timed sides are together.

-Line up nether notches and nose point.

-Peg together.

Step 10: Bias Tapeline Top and Bottom Edge (Premade Bias Tape Method)

-Add bias tape to the top and bottom edge. -You give notice use made diagonal tape measure, make your own bias tape, or bias taping attachment. All methods work.

-Sew in the twist tie when adding the bias tape to the top edge.

-BIAS TAPE TIE BACK OPTION: Pass on 10 inches at first and end of from each one edge. This will ease up you sufficiency bias videotape to link behind your head. Bank bill: you can ever shave the predetermine mag tape down if it is to long :)

-ELASTIC or CORD OPTION: Add predetermine tape along some edges. Coiffure not need to go past the sides.

Step 11: Making Bias Tape

-Use prejudice tape making kit.

-Cut bias tape to folder size.

-Feed bias tape though folder and iron.

Step 12: Double Fold Preconception Tape Attachment

-You seat also use a doubly fold preconception tape attachment to save fourth dimension. This will fold the bias tape and sew IT on at the same time.

Dance step 13: Bias Tape Tie In reply Method acting

-If you are choosing to use the preconception tape every bit the tie backs you are complete and can proceed onto the breathing valve step.

-I do recommend cleaning up the raw side edge to forestall fraying. This is best done before adding the bias taping.

Step out 14: Cord Method

-Cut cord at 24 inches. This leave give you sufficiency cord to tie around the hind of your head.

-Place the electric cord on the inside. Pealing the edge over and hem down.

-Do not sew over the cord. You lack the cord to side inside the hem.

Step 15: Elastic Method

-Cut 11 inches of lively.

-Same estimate as the cord method.

-Place the elastic along the exclusive. Scrol the edge ended and hem down.

-Do not sew over the rubberlike. You deficiency the cord to side inside the hem.

Step 16: Tie Elastic

-Tie the elastic ends unitedly.

-Actuate the knot into the hem.

Tread 17: Add Elastic Stoppers

-Elastic stopper are great for adjusting the size of the elastic loop.

-Pinch the elastic together and slew IT though the stopper.

Step 18: Adding Eupnoeic Valve

-Place back of breathing valve on the inside of the mask view the hole.

-Snap top on to secure on outer layer.

Step 19: ADHD Filter

-Attention deficit hyperactivity disorder pm2.5 percolate and you are done! :)

Step 20: Video Instruction manual

If you are having inconvenience figuring out any steps. I recommend checking impermissible the detailed video. I go through every footprint :)

Follow the Starting time to Share

Recommendations

  • Anything Goes Contest 2022

    Anything Goes Contest 2022